Advancing Industrial Efficiency: High Wear-Resistant Tread Antistatic Solid Rubber Tires
Feb 28,2024
Jan 15,2022
Frequent replacement of forklift tires is not a good thing. It is not only time-consuming but also causes a lot of waste. So Zhejiang Kunrong Rubber Technology Co., Ltd. hereby reminds you to use forklifts reasonably, which not only saves time and effort, but also ensures long-term safety/safety work. A guarantee, let's take a look: How to reduce the wear of forklift tires? 1. Strengthen the maintenance of tires.Do a good job of land survey and pressure cleaning, check the temperature of the tires, and the grounding holes are blocked.Usually when inflating tires, if it is cold and under a certain load, regularly check and adjust the tire pressure at least once a month; in summer, due to the high ambient temperature, if the tire temperature is too high, reduce the frequency of increase to avoid strong sunlight to the tires , it is recommended to stop in the shade of a tree, instead of directly pouring cold water for cooling or directly venting to reduce pressure. If you are going to leave it in the open parking lot for a long time in winter, you should base it on the tires and don't start accelerating immediately until the tires get hot, and then it becomes normal driving. 2. Improve driving skills.Lift the clutch pedal slowly and steadily when starting off. The maximum speed of driving must not exceed the speed limit of the tire; it should be avoided as much as possible during the process of rapid acceleration, emergency braking and sharp turning. In the case of obstacles such as rocks and potholes, it is recommended that you slow down as much as possible or avoid it directly.3. Improve the maintenance of the chassis.Lubricate and adjust the design value of wheel hub bearing, tie rod ball end, king pin bushing in time according to regulations; keep the balance of the tire, if it is unbalanced, the wheel dynamic balance test should be used to exhaust the one-way valve frequently, and the tire has been oiled. Once the forklift is found Tire into oil, you should immediately remove the tire to clean, and check the air seal at the same time, replace the tire winter tire in the greenhouse to restore / restore elasticity / elasticity, load the rim forklift tire product Apply soap in the fetal port to prevent damage to the port; pivot oil Sealing and brake hydraulic cylinders should be leak-free, and oil- and wet-resistant rubber tires should meet the requirements for lateral and radial swinging wheel assemblies.
View more +Dec 03,2021
1. Excellent safe use performance is conducive to improving work efficiencyBecause the solid tire carcass is made of all rubber, the puncture resistance of the tire is ensured to the greatest extent, and the hidden danger of tire puncture during the load-bearing operation of industrial vehicles and in the harsh working environment is fundamentally eliminated. The load-deformation of solid tires is small, and the running stability is good. Because of its puncture resistance and tear resistance, it does not need to be inflated. It avoids the heavy labor of frequent tire replacement and can improve the utilization rate and work efficiency of the vehicle. It can run at low speed and efficiently. In vehicles, solid tires can completely replace pneumatic tires.2. Reasonable structural design to ensure that the tire has better performanceThe solid tire adopts an advanced three-stage structure design, and the three rubber materials respectively ensure the overall performance of the tire. High-rigidity, high-strength base rubber and steel ring support not only ensure the stiffness of the tire, but also ensure the tightness between the tire and the rim, and fundamentally eliminate the slip ring problem of solid tires; the high-elastic intermediate rubber effectively It absorbs the vibration generated when the vehicle is running, and has a comfortable driving performance, while avoiding damage to the vehicle; the thicker tread rubber layer ensures the tire's resistance to tearing and abrasion, and improves the service life of the solid tire;3. Advanced technology and formula designThe production of solid tires has advanced technology with more than half a century of production history and experience. The rubber formula design has maximized the performance of the tires, especially the base rubber is all imported high-rigidity, low-heat-generating rubber materials. The heat generation and temperature rise during operation are minimized, while the heat resistance of the tire is improved, thereby solving the serious problems of solid tires such as swelling, slippage, and burst caused by temperature rise; advanced formula design reduces the tire The rolling resistance. Tested by the National Construction Machinery Quality Supervision and Inspection Center, the coefficient of rolling resistance of solid tires is equivalent to that of pneumatic tires, which solves the problem of increased fuel consumption caused by changing to solid tires;4. Avoid vehicle tire blowouts and out-of-control dangers, and promote safe productionPneumatic tire rim-type solid tire is a solid tire that can be used interchangeably with pneumatic tires of the same specification. When the vehicle is driving at high speed, such as the tire hitting potholes and other obstacles, the tire will be severely squeezed and deformed between the obstacle and the rim flange, which can cause the carcass cord to break, and the compressed air inside the tire will break. The line is pushed up to form a bulge. In more serious cases, it will cause the tyre to rupture, and it will be completely flattened instantly and the vehicle may lose control. Compared with pneumatic tires, it has the advantages of high safety, puncture resistance, tear resistance, wear resistance and long life. It is an ideal replacement product for pneumatic tires in the field of industrial vehicles. With the development of industrial vehicles and the improvement of solid tire production technology, this type of tire has been used more and more widely.
View more +Dec 03,2021
Because forklift solid tires have many advantages, solid tires have higher load performance, which can reduce the load area of tires and contact surfaces, greatly reduce tire wear machines, increase vehicle flexibility, and improve work efficiency. The inner part of the tire is filled with elastic adhesive paper. No matter it is used in any place, there is no tyre breakage or puncture. The design of multiple fastened travellers at the tire spigot can have sufficient strength to bear the weight and will not slip. It has good shock absorption performance, and the grip ability at room temperature and low temperature is combined with the pattern, and it is also suitable for roads in harsh environments.
View more +